| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 12259 : 2018 |
Ski-Poles for Alpine Skiing - Requirements and Test Methods (Second Revision) |
PGD 27 |
| 2 |
IS 10651 : 2019 |
Hub axle, front for moped - Specification (First Revision) |
TED 2 |
| 3 |
IS 10653 : 2019 |
Hub axle, rear, for moped - Specification (First Revision) |
TED 2 |
| 4 |
IS 14700 : Part 4 : Sec 1 : 2019 |
Electromagnetic compatibility (EMC): Part 4 testing and measurement techniques: Sec 1 overview of the IEC 61000 - 4 series (Second Revision) |
LITD 9 |
| 5 |
IS 9471 : Part 5 : Sec 2 : 2019 |
Specification for modular lower limb orthotic components: Part 5 joint unit section 2 standard knee |
MHD 9 |
| 6 |
IS 17166 : 2019 |
Technical product documentation -- Heat-treated ferrous parts -- Presentation and indications |
PGD 24 |
| 7 |
IS 1367 : Part 5 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 5 mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (Fourth Revision) |
PGD 37 |
| 8 |
IS 1367 : Part 6 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision) |
PGD 37 |
| 9 |
IS 1367 : Part 14 : Sec 3 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 14 mechanical properties of corrosion - Resistant stainless steel fasteners section 3 set screws and similar fasteners not under tensile stress (Fourth Revision |
PGD 37 |
| 10 |
IS 513 : Part 1 : 2016 |
Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision) |
MTD 4 |
| 11 |
IS 513 : Part 2 : 2016 |
Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision) |
MTD 4 |
| 12 |
IS 4217 : 2020 |
Rolling bearings -- Needle rollers -- Specification (Second Revision) |
PGD 13 |
| 13 |
IS 9202 : 2020 |
Rolling Bearings — Cylindrical Rollers — Specification ( First Revision ) |
PGD 13 |
| 14 |
IS 13614 : Part 1 : 1995 |
Hydraulic fluid power - Quick action couplings: Part 1 dimensions and requirements |
PGD 36 |
| 15 |
IS 15935 : 2011 |
Composite cylinders for on - Board storage of compressed natural gas (CNG) as a fuel for automotive vehicle - Specification |
MED 16 |
| 16 |
IS 963 : 1958 |
Specification for chrome molybdenum steel bars and rods for aircraft purposes |
MTD 16 |
| 17 |
IS 11946 : 1987 |
Specification for soft magnetic iron strips |
MTD 16 |
| 18 |
IS 11947 : 1987 |
Specification for soft magnetic iron rods, bars, flats and sections |
MTD 16 |
| 19 |
IS 9295 : 1983 |
Specification for steel tubes for idlers for belt conveyors (First Revision) |
MTD 19 |
| 20 |
IS 11714 : Part 1 to 5 : 1986 |
Specification for steel tubes for heat exchangers |
MTD 19 |
| 21 |
IS 15045 : Part 2 : 2021 |
Pneumatic Fluid Power - Five-Port Directional Control Valves Part 2 Mounting Interface Surfaces with Optional Electrical Connector ( First Revision ) |
PGD 36 |
| 22 |
IS 13302 : 2003 |
Rough Terrain Fork-Lift Trucks - Stability Test |
TED 22 |
| 23 |
IS 16143 : Part 8 : 2021 |
Hard coal and coke - Mechanical sampling : Part 8 methods of testing for bias (First Revision) |
PCD 7 |
| 24 |
IS 17582 : 2021 |
Specification for Infantometer |
PGD 26 |
| 25 |
IS 1586 : Part 2 : 2018 |
Metallic materials - Rockwell hardness test: Part 2 verification and calibration of testing machines and indenters (Fifth Revision) |
MTD 3 |
| 26 |
IS 7028 : Part 9 : 2020 |
Packaging -- Complete filled transport packages -- Compression and stacking tests using a compression tester |
TED 24 |
| 27 |
IS 17676 : Part 1 : 2021 |
Guidelines for the management of assets of water supply and wastewater systems Part 1:Drinking water distribution networks |
SSD 14 |
| 28 |
IS 17677 : 2021 |
GUIDELINES FOR HEALTH RISK ASSESSMENT AND MANAGEMENT FOR NON-POTABLE WATER REUSE |
CHD 32 |
| 29 |
IS 6416 : 1988 |
Methods for measuring case depth of steel (First Revision) |
MTD 22 |
| 30 |
IS 2303 : Part 1 : Sec 2 : 2021 |
GRADING GLASS FOR ALKALINITY PART 1 HYDROLYTIC RESISTANCE OF GLASS GRAINS SECTION 2 DETERMINATION AND CLASSIFICATION OF HYDROLYTIC RESISTANCE AT 121C |
CHD 10 |
| 31 |
IS 16978 : Part 1 : 2018 |
Glass in building - Forced - Entry security glazing: Part 1 test and classification by repetitive ball drop |
CHD 10 |
| 32 |
IS 11169 : Part 1 : 1984 |
Specification for steels for cold heading/cold extrusion applications: Part 1 wrought carbon and low alloy steels |
MTD 16 |
| 33 |
IS 3748 : 1990 |
Tool and die steels - Specification (Second Revision) |
MTD 16 |
| 34 |
IS 1367 : Part 14 : Sec 1 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 14 mechanical properties of corrosion - Resistant stainless - Steel fasteners section 1 bolts, screws and studs (Fourth Revision) |
PGD 37 |
| 35 |
IS 6001 : 1971 |
Specification for flyer spindles |
TXD 14 |
| 36 |
IS 1367 : Part 14 : Sec 2 : 2018 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless steel Fasteners Section 2 Nuts (Fourth Revision) |
PGD 37 |
| 37 |
IS 2699 : 1982 |
Specification for flats and flats' screws (first revision) |
TXD 14 |
| 38 |
IS 3078 : 1989 |
Rings for spinning and doubling frames – Specification (fourth revision) |
TXD 14 |
| 39 |
IS 3934 : 1989 |
Aluminium plug type spindles for spinning and doubling frames – Specification (second revision) |
TXD 14 |
| 40 |
IS 8800 : 1997 |
Technical delivery conditions for steel castings (Excluding Investment Castings) (Third Revision) |
MTD 14 |
| 41 |
IS 17631 : 2022 |
Work Chairs - Specification |
CED 35 |
| 42 |
IS 6913 : 1973 |
Specification for stainless steel tubes for the food and beverage industry |
MTD 19 |
| 43 |
IS 8137 : 1976 |
Specification for springs for plain calico looms |
TXD 14 |
| 44 |
IS 8138 : 1976 |
Specification for picking nose, boss and shell for looms |
TXD 14 |
| 45 |
IS 8139 : 1976 |
Specification for picking cone and bolt for looms |
TXD 14 |
| 46 |
IS 11508 : 1985 |
Specification for faller bars for jute drawing frames |
TXD 14 |
| 47 |
IS 12885 : 1990 |
Pressing roller assembly for jute drawing frame - Specification |
TXD 14 |
| 48 |
IS 12886 : 1990 |
Heart cam for jute spinning frame - Specification |
TXD 14 |
| 49 |
IS 7494 : 1981 |
Specification for steel for valves for internal combustion engines (First Revision) |
MTD 16 |
| 50 |
IS 14677 : 1999 |
Spindles with bolsters for CHARKHAS – Specification |
TXD 14 |
| 51 |
IS 5824 : 1970 |
Specification for lancets for use in foundries |
MTD 14 |
| 52 |
IS 6013 : 1970 |
Specification for trowels for use in foundries |
MTD 14 |
| 53 |
IS 6268 : 1971 |
Specification for accessories for use in shuttles for plain calico looms |
TXD 14 |
| 54 |
IS 5841 : 1970 |
Specification for fluted core cleaners for use in foundries |
MTD 14 |
| 55 |
IS 13221 : 1991 |
Textile machinery – Cams, faller screw for screw gill jute drawing frame – Specification |
TXD 14 |
| 56 |
IS/IEC 60372 : 1984 |
Locking devices for ball and socket couplings of string insulators units - Dimensions and tests |
ETD 6 |
| 57 |
IS 11512 : 1985 |
Specification for faller screws for jute drawing frames |
TXD 14 |
| 58 |
IS 17902 : 2022 |
Animal feeding stuffs Determination of amylase-treated neutral detergent fibre content ANDF |
FAD 5 |
| 59 |
IS 17903 : 2022 |
Animal feeding stuffs Determination of acid detergent fibre ADF and acid detergent lignin ADL contents |
FAD 5 |
| 60 |
IS 2744 : 2022 |
1-Naphthylamine (Second Revision) |
PCD 26 |
| 61 |
IS 10795 : 1984 |
Specification for accessories for use in shuttles for pirn-changing automatic cotton looms |
TXD 14 |
| 62 |
IS 11510 : 1985 |
Specification for spindle for jute cop winding machine |
TXD 14 |
| 63 |
IS 12658 : 1989 |
Grinding media rolled/forged carbon and Carbon - Chromium steels - Specification |
MTD 16 |
| 64 |
IS 3494 : 1978 |
Specification for Pruning Secateur (First Revision) |
FAD 11 |
| 65 |
IS 3848 : 1981 |
Method for end quench test for hardenability of steel (First Revision) |
MTD 22 |
| 66 |
IS 6603 : 2001 |
Stainless steel bars and flats - Specification (First Revision) |
MTD 16 |
| 67 |
IS 3122 : 1982 |
Specification for Budding and Grafting Knife Combined (First Revision) |
FAD 11 |
| 68 |
IS 7898 : 2001 |
Manually - Operated Chaff Cutter - Specification (Second Revision) |
FAD 20 |
| 69 |
IS 2151 : 2022 |
Maize Germ Oilcake as Livestock Feed Ingredient � Specification |
FAD 5 |
| 70 |
IS 2095 : Part 3 : 2022 |
Gypsum Plaster Boards — Specification Part 3 Reinforced Gypsum Plaster Boards and Ceiling Tiles ( Fourth Revision ) |
CED 4 |
