Home About Standards Downloads Reports Standard Of The Week Standard Of The Month FAQ Contact Us
�

Indian Standard Details

    Print

Basic Details
IS Number : IS 6603:2024
IS Title [Eng-Hn] : Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars — Specification (Second Revision)
No of Revision : 2
No of Amendments : 0
Technical Department : Metallurgical Engineering Department
Technical Committee : MTD 16 ( Alloy Steels and Forging Sectional Committee )
Language : English

Classification Details
Group : Metals, Alloys and Metal Products (including Steel Products)
Sub Group: Steel and Steel Castings, Wires, Ropes, Pipes , Tubes and other products
Sub Sub Group : Hot rolled steel sheet & plates
Aspects: Product Specification
Certification:
Ministry : Ministry of Steel
Short Commom Man's Title: Stainless steel bars and flats
Itchs:
Degree of Equivalence: Not Equivalent
Identical/Equivalent Standards:ISO I6143-2
Organisation :

Cross Referencing Details
Indian Standards Refered In IS IS 6603 : 2024 :
SNo IS Number Title Technical Committee
1
IS 228 : Part 1 : 1987 Methods for chemical analysis ofsteels: Part 1 determination ofcarbon by volumetric method (For Carbon 0.05to 2.50 Percent) (Third Revision) MTD 34
2
IS 919 : Part 1 : 2014 Geometrical Product Specifications (GPS) - ISO Code System for Tolerances on Linear Sizes Part 1 Basis of Tolerance, Deviation and Fits (Third Revision) PGD 37
3
IS 1500 : Part 1 : 2019 Metallic materials - Brinell hardness test: Part 1 test method (Fifth Revision) MTD 03
4
IS 1501 : Part 1 : 2020 Metallic Materials — Vickers Hardness Test Part 1 Test Method ( Fifth Revision ) MTD 03
5
IS 1586 : Part 1 : 2018 Metallic materials - Rockwell hardness test: Part 1 test method (Fifth Revision) MTD 03
6
IS 1599 : 2019 Metallic materials - Bend test (Fourth Revision) MTD 03
7
IS 1608 : Part 1 : 2022 Metallic materials - Tensile testing - Part 1 : Method of test at room temperature ( Fifth Revision) MTD 03
8
IS 1608 : Part 2 : 2020 Metallic Materials - Tensile Testing Part 2 Method of Test at Elevated Temperature ( Fourth Revision ) MTD 03
9
IS 1757 Part 1 : 2020 Metallic Materials — Charpy Pendulum Impact Test Part 1 Test Method ( Fourth Revision ) MTD 03
10
IS 1762 : Part 1 : 1974 Code for designation of steels: Part 1 based on letter symbols (First Revision) MTD 04
11
IS 1956 : Part 3 : 2019 Glossary of terms relating to iron and steel: Part 3 long products (Including Bars, Rods, Sections And Wires) (Second Revision) MTD 04
12
IS 3711 : 2020 Steel and Steel Products — Location and Preparation of Samples and Test Pieces for Mechanical Testing ( Third Revision ) MTD 03
13
IS 8910 : 2022 General technical delivery requirements for steel and steel products MTD 04
14
IS/ISO 10474 : 2013 Steel And Steel Products — Inspection--Documents MTD 04
15
IS/ISO 14284 : 1996 Steel and iron - Sampling and preparation of samples for the determination of chemical composition MTD 04
16
IS 10461 : Part 1 : 1994 Resistance to inter - Granular corrosion of austenitic stainless steels - Method for determination - Part 1 : corrosion test in nitric acid medium by measurement of loss in mass (Huey Test) (First Revision) MTD 24
International Standards Refered In IS 6603 : 2024 Standard contains no Cross Referenced International Standard.
IS 6603 : 2024 is Refered in following Indian Standards :
SNo IS Number Title Technical Committee
1 IS 7398 : 1974 Specification For Forceps, Bone Holding, Farabeuf's Pattern MHD 02
2 IS 8332 : 1977 Specification for handle, saw, Gigli MHD 02
3 IS 7819 : 1975 Specification for mallet, nylon headed, orthopaedic MHD 02
4 IS 5747 : 1970 SPECIFICATION FOR RETRACTOR, ENDAURAL ( LEMPERT'S PATTERN ) MHD 04
5 IS 5580 : 1970 Specification for chisels, stille pattern, orthopaedic MHD 02
6 IS 6319 : 1971 Specification for clamp, bone, Lowman type MHD 02
7 IS 11904 : 2023 Rolling bearings Radial bearings with locating snap ring Dimensions geometrical product specifications GPS and tolerance values PGD 13
8 IS 8695 : 1978 Specification for Forceps, Dressing, Bayonet Shape, Cushing's Pattern MHD 07
9 IS 8334 : 1977 Rongeur, Cranial, Dahlgren's Pattern MHD 07
10 IS 5290 : 1993 Landing valves - Specification (Third Revision) CED 22
11 IS 7710 : 1975 Specification for Snare Tonsil, Eve’s Pattern MHD 04
12 IS 7713 : 1975 Specification for Retractor, Light Model, Weislander’s Pattern MHD 04
13 IS 9718 : 1981 Specification for jig, cutting, ptfe piston MHD 04
14 IS 13169 : 1991 Ent surgery instruments head mirror - Specification MHD 04
15 IS 12175 : 1987 Specification for rapid moisture meter for rapid determination of water content for soil CED 43
16 IS 10088 : 1981 Specification for retractor, dental MHD 08
17 IS 10309 : 1982 Specification for key, torquing, edgewise MHD 08
18 IS 7109 : 1973 Specification for starter, staple, orthopaedic MHD 02
19 IS 7111 : 1973 Specification for inserter, staple, orthopaedic MHD 02
20 IS 10963 : 1984 Specification for forceps, hoof testing MHD 13
21 IS 11196 : 1985 Specification for equipment for determination of liquid limit of soils cone penetration met - Hod CED 43
22 IS 3025 : Part 8 : 2023 Methods of Sampling and Test Physical and Chemical For Water and Wastewater Part 8 Taste Rating Second Revision CHD 36
23 IS 8418 : 1999 Pumps - Centrifugal self priming - Specification (First Revision) MED 20
24 IS 5829 : 1982 Specification for sound, uterine (First Revision) MHD 03
25 IS 12271 : 1988 Specification for laproscopic trocar and cannula MHD 03
26 IS 6957 : 1973 Specification for curette, blunt, uterine MHD 03
27 IS 7885 : 1985 Spray, Macintosh's Pattern MHD 11
28 IS 8312 : 1977 Forceps, Introducing, Endotracheal Tube, Magill's Pattern MHD 11