| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 12511 : Part 2 : 2004 |
Springs - Disc spring: Part 2 specification (First Revision) |
TED 34 |
| 2 |
IS 5522 : 2014 |
Stainless steel sheets and strips for utensils - Specification (Third Revision) |
MTD 16 |
| 3 |
IS 3075 : Part 1 : 1986 |
Specification for circlips: Part 1 for shafts (First Revision) |
PGD 35 |
| 4 |
IS 3075 : Part 3 : 1986 |
Specification for circlips: Part 3 type e for shafts (First Revision) |
PGD 35 |
| 5 |
IS 3019 : 1973 |
Specification for high speed steel butt -- Welded single point turning tools (first revision) |
PGD 32 |
| 6 |
IS 8405 : 2005 |
Thread rolling cylindrical dies -- Specification (first revision) |
PGD 32 |
| 7 |
IS 15490 : 2017 |
Seamless steel cylinders for on - Board storage of compressed natural gas as a fuel for automotive vehicles - Specification (First Revision) |
MED 16 |
| 8 |
IS 4071 : 1986 |
Specification for Master Gears (first revision) |
PGD 33 |
| 9 |
IS 413 : 1974 |
Specification for round punches (Second Revision) |
PGD 34 |
| 10 |
IS 552 : 1965 |
Specification for smith bits (Revised) |
PGD 34 |
| 11 |
IS 10489 : 1983 |
Specification for steel dresser for abrasive wheels |
PGD 9 |
| 12 |
IS 7285 : Part 2 : 2017 |
Refillable seamless steel gas cylinders - Specification: Part 2 quenched and tempered steel cylinders with tensile strength less than 1 100 mpa (112 Kgf/mm²) (Fourth Revision) |
MED 16 |
| 13 |
IS 7285 : Part 1 : 2018 |
Refillable seamless steel gas cylinders - Specification: Part 1 normalized steel cylinders (Fourth Revision) |
MED 16 |
| 14 |
IS 15029 : 2001 |
Recovery taps for use with diamond core drilling - Requirements |
MED 21 |
| 15 |
IS 3513 : Part 1 : 1989 |
Resin treated compressed wood laminates (compregs) - Specification Part 1 For electrical purposes |
CED 20 |
| 16 |
IS 3513 : Part 2 : 1989 |
Resin treated compressed wood laminates (compregs) - Specification Part 2 For chemical purposes |
CED 20 |
| 17 |
IS 3513 : Part 3 : 1989 |
Resin Treated Compressed Wood Laminates (Compregs) - Specification Part 3 : For General Purposes |
CED 20 |
| 18 |
IS 6007 : 1971 |
Specification for pipe vices (Hinged Type) |
PGD 34 |
| 19 |
IS 6087 : 1971 |
Specification for metal cutting shears |
PGD 34 |
| 20 |
IS 7177 : 1974 |
Specification for centre punches |
PGD 34 |
| 21 |
IS 13093 : 2002 |
Sheet metal body repair steel hammers - General requirements (First Revision) |
PGD 34 |
| 22 |
IS 9873 : Part 1 : 2019 |
Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision) |
PCD 30 |
| 23 |
IS 12297 : 1988 |
Specification for delivery roller boss for jute drawing frame |
TXD 14 |
| 24 |
IS 12307 : 1988 |
Specification for delivery pressing roller boss for jute drawing frame |
TXD 14 |
| 25 |
IS 13682 : 1993 |
Textile machinery and accessories - Bobbin rail pin and plate for jute spinning frame - Specification |
TXD 14 |
| 26 |
IS 13720 : 1993 |
Textile machinery and accessories - Pressing roller assembly for jute spinning frame - Specification |
TXD 14 |
| 27 |
IS 14675 : 1999 |
Bottom drafting rollers for CHARKHAS – Specification |
TXD 14 |
| 28 |
IS 14711 : 1999 |
Textile machinery and accessories – Frame components of CHARKHAS – Specification |
TXD 14 |
| 29 |
IS 13752 : 1993 |
Guidelines for reporting sequence of elements in steel and pig iron and mechanical properties in steels |
MTD 4 |
| 30 |
IS 8461 : 1987 |
Specification for cane knives (First Revision) |
FAD 2 |
| 31 |
IS 7043 : 1973 |
Specification for loom (fly) spindles |
TXD 14 |
| 32 |
IS 2181 : 1973 |
Specification for sewing machine needles for household purposes (First Revision) |
MED 29 |
| 33 |
IS 11872 : Part 1 and 2 : 1987 |
Specification for rollers for drawing and spinning frames in jute mill |
TXD 14 |
| 34 |
IS 11872 : Part 2 : 1987 |
Specification for rollers for drawing and spinning frames in jute mill |
TXD 14 |
| 35 |
IS 11898 : 1986 |
Specification for faller bar slides for jute drawing frames |
TXD 14 |
| 36 |
IS 11899 : 1986 |
Specification for flyers for jute spinning frames |
TXD 14 |
| 37 |
IS 6755 : 1980 |
Specification for double coil helical spring washers (First Revision) |
PGD 37 |
| 38 |
IS/ISO 2415 : 2004 |
Forged shackles for general lifting purposes - Dee shackles and bow shackles |
MED 14 |
| 39 |
IS 9143 : 1979 |
Method for the determination of unconfined compressive strength of rock materials |
CED 48 |
| 40 |
IS 923 : 1965 |
Carving Knives |
MED 33 |
| 41 |
IS 9221 : 1979 |
Method for the determination of modulus of elasticity and Poisson's ratio of rock materials in uniaxial compression |
CED 48 |
| 42 |
IS 921 : 1965 |
Butcher's Knives |
MED 33 |
| 43 |
IS 13380 : 1992 |
Forestry tools - Hole punch, bow saw blades - Specification |
PGD 34 |
| 44 |
IS 4296 : Part 1 : 2016 |
Tools for pressing: Part 1 round punches with 60 degrees conical head and straight shank (Second Revision) |
PGD 4 |
| 45 |
IS 822 : 1970 |
Code of procedure for inspection of welds |
MTD 11 |
| 46 |
IS 4215 : 1983 |
Specification for ring type needle bearings (First Revision) |
PGD 13 |
| 47 |
IS 6571 : 1991 |
Rehabilitation equipment - Wheelchairs, non - Folding, adult size, institutional model - Specification (First Revision) |
MHD 9 |
| 48 |
IS 7454 : 1991 |
Rehabilitation equipment - Wheelchairs, folding, adult size - Specification (First Revision) |
MHD 9 |
| 49 |
IS 8086 : 1991 |
Rehabilitation equipment - Wheelchairs, folding, junior size - Specification (First Revision) |
MHD 9 |
| 50 |
IS 3510 : 1990 |
Engineering Metrology - Toolmaker Flats - Specification ( First Revision ) |
PGD 25 |
| 51 |
IS 12549 : 1988 |
Specification for iron nickel cobalt sealing alloy |
MTD 16 |
| 52 |
IS 6911 : 2017 |
Stainless steel plate, sheet and strip - Specification (Second Revision) |
MTD 16 |
| 53 |
IS 2563 : 1978 |
Specification for Hedge Sears, Straight - Edge Type (First Revision) |
FAD 11 |
| 54 |
IS 3108 : 1991 |
Forestry Tools - Pruning Saw - Specification (Second Revision) |
FAD 11 |
| 55 |
IS 4358 : 1996 |
Specification for Sickles (First Revision) |
FAD 11 |
| 56 |
IS 15277 : 2002 |
Metallic tube connections for fluid power and general use test methods for threaded hydraulic fluid power connections |
PGD 36 |
| 57 |
IS 15184 : 2002 |
Bicycles - Steel balls - Specification |
TED 16 |
| 58 |
IS 13374 : 1992 |
Forestry Tools - Handsappie, Nursery (Kutla) - Specification |
FAD 11 |
| 59 |
IS 13376 : 1992 |
Forestry Tools - Debarking Spud - Specification |
FAD 11 |
| 60 |
IS 13377 : 1992 |
Forestry Tools - Shrub Cutting Knife - Specification |
FAD 11 |
| 61 |
IS 13378 : 1992 |
Forestry Tools - Felling Lever - Specification |
FAD 11 |
| 62 |
IS 3391 : 1965 |
Specification for stethoscopes |
MHD 11 |
| 63 |
IS 14525 : 1998 |
Forestry Tools - Seed Plucker - Specification |
FAD 11 |
| 64 |
IS 14540 : 1998 |
Intercultivation Equipment - Hand Hoes - Specification |
FAD 11 |
| 65 |
IS 14541 : 1998 |
Forestry and Plantation Tools - Hoes and Forks - Specification |
FAD 11 |
| 66 |
IS 1511 : 1979 |
Specification for Blades for Manually - Operated Chaff Cutter (Second Revision) |
FAD 20 |
| 67 |
IS 5224 : 1993 |
Qilseeds Milling Machinery - Oil Expellers Single Barrel - Specification (Second Revision) |
FAD 13 |
| 68 |
IS 13794 : 1993 |
Oilseeds Milling Machinery - Power Ghanies Portable - Specification |
FAD 13 |
| 69 |
IS 7825 : 2004 |
Cylinder Type Hand Lawn Mower Specification (First Revision) |
FAD 11 |
| 70 |
IS 810 : 1991 |
Internal combustion engines - Engine valves - Specification (Second Revision) |
TED 2 |
| 71 |
IS 10628 : 1983 |
General requirements for aerospace bolts and nuts |
TED 14 |
| 72 |
IS B9813 : 2002 |
Tractor - Operated Blade Terracer - Specification (First Revision) |
FAD 11 |
| 73 |
IS 1367 : Part 3 : 2017 |
Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision) |
PGD 37 |
| 74 |
IS 15894 : 2018 |
Inspection gauges for checking taper threads of gas cylinder valves and cylinder necks - Taper 1 in 16 on diameter - Specification (First Revision) |
MED 16 |
| 75 |
IS 17063 : 2018 |
Specification for rehabilitation equipment ? rough terrain active wheelchairs, folding, rider - I, adult and child size |
MHD 9 |
| 76 |
IS 1448 : Part 149 : 2020 |
Methods of Test for Petroleum and its Products Part 149 Diesel Fuel - Assessment of Lubricity Using the High - Frequency Reciprocating Rig ( HFRR ) - Test Method ( Second Revision ) |
PCD 1 |
| 77 |
IS 7202 : 2017 |
Inspection gauges for checking type 4 (Size 1, 2, 3) taper threads of gas cylinder valves and cylinder necks - Specification (First Revision) |
MED 16 |
