Standards in Category :: Equipment for irrigation

 

SI. No.
IS Number
Product
Features
Action
1.
 IS 15500 (Part 1 to 8) : 2021
 Deepwell Handpump This standard covers handpumps which are suitable for lifting water from deep set borewells, covering static water level (SWL) range from 20 m to 90 m. Various type of Handpumps like Standard (SDWP), VLOM 50, VLOM 65, Extra Deep (EDWP) and Force Lift (FLP) are covered in this standard. This standard specifies nomenclature, dimensions, tolerances, material and testing requirements for deepwell handpumps. View IS Detail
2.
 IS 8035 : 2022
 Shallow Well Handpump This standard covers handpumpss for lifting water from wells having static water level not exceeding 7 m below ground level. This standard scpecifies the material, dimensional, anti-corrosive tretament (Electro and hot-dip galvanizing ) and testing requirements for shallow well handpumps. View IS Detail
3.
 IS 14106 : 2018
 Direct Action Handpump This standard covers handpumps suitable for lifting water from borewells with static water level not exceeding 15 m. This standard specifies nomenclature, dimensions, tolerances, material and testing requirements for direct action handpumps. View IS Detail
4.
 IS 17018 (Part 1) : 2022
 Solar Photovoltaic Water Pumping Systems This specification (Part 1) covers design qualifications and performance specifications for Centrifugal Solar Photovoltaic (SPV) Water Pumping Systems from 0.75 kW up to 7.5 kW to be installed on a suitable bore-well, open well, water reservoir, water stream, etc. This standard includes terminology, design, performance and safety features for solar photovoltaic water pumping systems and also prescribes the methods of measurement of performance and energy efficiency ratings. View IS Detail
5.
 IS 8034 : 2018
Reviewed In : 2022		 Submersible pumpsets This Standard specifies the requirements for submersible pumpsets (single/multi stage) using single/ three phase AC induction motor, commonly used in boreholes (borewells or tubewells) for handling clear, cold water for application in agriculture and water supplies purposes. View IS Detail
6.
 IS 9079 : 2018
Reviewed In : 2022		 Monoset Pumps for Clear, Cold Water for Agricultural and Water Supply Purposes This Indian Standard specifies the requirements for monoset pumps (single/multi stage) using single/three phase a.c. induction motor/motor portion for handling clear, cold water for agricultural and water supply purposes. View IS Detail
7.
 IS 8472 : 2019
Reviewed In : 2019		 Centrifugal regenerative pumps for clear, cold water This standard specifies the technical requirements for centrifugal regenerative pumps that is, repeated centrifugal action pumps for handling clear, cold water. The pump may be constructed either as a bare pump or monoset in single or multi-stage construction. View IS Detail
8.
 IS 12785 : 1994
Reviewed In : 2021		 Strainer type Filters In drip irrigation system, the strainer type filters are used for an efficient and trouble-free operation of the drippers as the drippers have small narrow passages and may cause hazard of blocking or clogging by impurities present in the irrigation water. This standard specifies the general construction requirements and test methods for strainer type filters intended for operation in agricultural irrigation systems. View IS Detail
9.
 IS 12232 (Part 1) : 1996
ISO 7749-1
Reviewed In : 2021		 Rotating Sprinkler This device uses its rotating motion around its vertical axis to distribute water over a circular area or part of a circular area in agriculture field. This standard specifies the design and operational requirements of rotating sprinklers and sprinkler nozzles for agricultural irrigation equipment and their test methods. View IS Detail
10.
 IS 12786 : 1989
Reviewed In : 2021		 Polythene pipes for irrigation laterals Drip irrigation systems is one of the modern irrigation techniques to economise the use of water in agriculture. This standard lays down requirements for polyethylene pipes of outside diameter from 12 mm up to 32 mm to be used for irrigation laterals (branch supply lines on which sprayers or drippers or emitters are mounted directly or by means of a fitting or formed in the pipe during production) in drip irrigation. View IS Detail
11.
 IS 13487 : 1992
Reviewed In : 2021		 Emitters This is fitted to an irrigation lateral in drip irrigation system and intended to emit water in the form of drops or continuous flow at specific emission rate. This standard specifies mechanical and functional requirements of irrigation emitters to permit correct installation and operation in the field. View IS Detail
12.
 IS 13488 : 2008
Reviewed In : 2021		 Emitting pipe Systems This standard specifies the mechanical and functional requirements of the emitting pipes and their fittings to facilitate correct installation and operation in the field. This standard applies to emitting and trickling pipes, hoses and tubings intended for irrigation. View IS Detail
13.
 IS 14483 (Part 1) : 1997
Reviewed In : 2021		 Venturi Injector Venturi injector is used to apply fertilizer materials or/and other chemicals through irrigation water to crop plant and uses the principle that a swiftly moving stream of water is able to carry with it the dissolved substances and fine dispersed/ suspended particles of materials. This standard prescribes the constructional andf performance requirements of Venturi Injectors used for injecting fertilizer and chemicals in the sprinkler and drip irrigation systems. View IS Detail
14.
 IS 14483 (Part 3) : 2018
Reviewed In : 2023		 Fertiliser Tank This standard specifies the mechanical and functional requirements for fertilizer tanks used in irrigation systems to permit correct installation and operation in the field. This standard applies to fertilizer tanks working on the principle of differential pressure used in irrigation systems to inject fertilizer/chemical solution for injection into an irrigation system. View IS Detail
15.
 IS 14605 : 1998
Reviewed In : 2021		 Micro Sprayers This standard specifies the general requirements and test methods for micro sprayers. It applies to sprayers intended for assembly in pipeline networks for irrigation and for operation with irrigation water. View IS Detail
16.
 IS 14606 : 2022
 Granulated Media Filters A Granulated media filter is basically a tank filled with sand or Gravel of appropriate size and grade suitable for micro irrigation systems often used with Emitting pipe systems and with emitter (dripper) systems, particularly where the water is from a surface source such as stream or reservoir. This standard specifies the construction requirements, operational & performance requirements and test methods for granulated media filters for operation in agricultural irrigation systems. View IS Detail
17.
 IS 14743 : 1999
Reviewed In : 2021		 Hydrocyclone filters Hydrocyclone filters are essentially used to separate sand from a tube well water or silt from river water for micro irrigation. This standard specifies the general constructional requirements and test methods of the hydrocyclone filters, intended for operation in agricultural irrigation systems. View IS Detail
18.
 IS 17425 : 2020
 Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation This standard lays down the general requirements for raw materials, manufacturing and testing of quick coupled and plain polyethylene pipes and fittings of outside diameters 40 mm to 200 mm used for portable sprinkler and drip irrigation systems as mains, sub mains or laterals. View IS Detail
19.
 IS 4985 : 2021
 Unplasticized Polyvinyl Chloride (UPVC) Pipes and fittings (injection moulded or fabricated) for potable water supplies A suitable alternative to metal pipes are the unplasticized polyvinyl chloride pipes which can be used to carry water. The Standard provides requirements for dimensions (diameter, wall thickness, ovality), properties like pressure carrying capacity, long service life, no effect on potable water (in case of pipes for potable water supply/hot and cold water installations) View IS Detail
20.
 IS 12231 : 1987
Reviewed In : 2018		 uPVC Pipes and uPVC fittings for agricultural pumpsets A suitable alternative to metal pipes are the unplasticized polyvinyl chloride pipes which can be used to carry water. Such uPVC pipes require fittings made using uPVC. The Standards provide requirements for dimensions (diameter, wall thickness, ovality), properties like pressure carrying capacity, long service life, no effect on potable water (in case of pipes for potable water supply/hot and cold water installations) of the pipes and associated fittings. View IS Detail
21.
 IS 12818 : 2010
Reviewed In : 2021		 uPVC screen pipes for borewells Screen pipes and casing pipes made using uPVC are commonly preferred in borewells/ tubewells. Such pipes need to be sturdy enough to withstand pressure from the soil and also pressure due to future reboring/ flushing. The Standard covers the essential requirements such as resistance to external blows, thread dimensions & profile, softening temperature, etc for use in deep wells and medium wells. View IS Detail
22.
 IS 9694 (Part 1) : 2023
 Selection, Installation, Operation and Maintenance of Horizontal Centrifugal Pumps for Agriculture Application — Code of Practice Part 1 Selection (Second Revision) This standard specifies that the general guidelines for the selection of horizontal centrifugal pumps for agricultural applications, excluding submersible and vertical turbine pumps. View IS Detail

Note 1 : For details of any specific Indian Standard, please access our Know your Standards feature on BIS website (www.bis.gov.in ) or BIS Care App

Note 2 : For complete list of Indian Standard, please go to our Published Standard feature of Standardization portal (www.manakonline.in).