BUREAU OF INDIAN STANDARDS
Programme of Work
TED2 : Automotive Primemovers, Transmission Systems and Internal Combustion Engine
- Scope : a) Standardization relating to automotive engines and transmission, components, Stationary Internal Combustion engines for agriculture and general. b) Co-ordination of work with ISO/ TC 22 and its Sub-committee ISO/ TC 22/ SC 34, c) Co-ordination of work with ISO/ TC 70 and its Sub-committees ISO/ TC 70/ SC 7 and ISO/ TC 70/ SC 8.
-
Liaison :ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids - Participating (P)
ISO/TC 22/SC 34/WG 1 - Fuel filters
ISO/TC 22/SC 34/WG 3 - Air filters
ISO/TC 70 - Internal combustion engines - Participating (P)
ISO/TC 70/SC 7 - Tests for lubricating oil filters - Participating (P)
ISO/TC 70/SC 7/WG 2 - Review of the no-reproducibility of Round Robin filtration efficiency results
ISO/TC 70/SC 8 - Exhaust gas emission measurement - Participating (P)
|
IS/ISO -10:2022 ISO 8528-10:2022 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 10 Measurement of Airborne Noise (First Revision)
|
-
|
Identical under single numbering
|
||
|
IS 10000 (Part 5):1980 |
Methods of tests for internal combustion engines: Part 5 preparation for tests and measurements for wear
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 10000 (Part 6):1980 |
Methods of tests for internal combustion engines: Part 6 recording of test results
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 10000 (Part 7):1980 |
Methods of tests for internal combustion, engines: Part 7 governing tests for constant speed engines and selection of engines for use with electrical generators
|
November, 2020
|
2
|
Indigenous
|
|
|
IS 10000 (Part 8):1980 |
Methods of tests for internal combustion engines Part 8 performance tests
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 9):1980 |
Methods of tests for internal combustion engines: Part 9 endurance tests
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 10):1980 |
Methods of tests for internal combustion engines: Part 10 tests for smoke levels, limits and corrections for smoke levels for variable ,speed compression ignition engines
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 12):1980 |
Methods of tests for internal combustion engines: Part 12 specimen test certificates
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 4):1980 |
Methods of tests for internal combustion engines: Part 4 declaration of power, efficiency, fuel consumption and lubricating oil consumption
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 10000 (Part 1):1980 |
Methods of tests for internal combustion engines: Part 1 glossary of terms relating to test methods
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 11):1980 |
Methqds of tests for internal combustion engines: Part 11 information to be supplied by the purchaser to the manufacturer and information to be supplied by the manufacturer along with the engine
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 10000 (Part 13):2002 |
Methods of tests for internal combustion engines: Part 13 recommendations on nature of tests required for functional changes in critical components
|
May, 2025
|
1
|
Indigenous
|
|
|
IS 10000 (Part 2):1980 |
Methods of tests for internal combustion engines Part 2 standar d reference conditions
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 10000 (Part 3):1980 |
Methods of tests for internal combustion engines: Part 3 measurements for testing - Units and limits of accuracy
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 10001:1981 ISO 3046 |
Performance Requirements for Constant Speed Compression ignition (diesel) engines for general purposes (up to 20 kW)
|
July, 2021
|
6
|
Modified/Technically Equivalent
|
|
|
IS 10002:1981 ISO 3046 |
Specification for performance requirements for constant speed compression ignition (Diesel) engines for general purposes (Above 20 KW)
|
July, 2021
|
3
|
Modified/Technically Equivalent
|
|
|
IS 10105:1982 Decision taken to Reaffirm and Archive |
Specification for fittings for cylinder pressure indicators for internal combustion engines
|
January, 2024
|
1
|
Indigenous
|
|
|
IS 10323:2019 Decision taken to Reaffirm and Archive |
Crank and chain wheel for moped - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 10478:2018 ISO 6519 : 2015 Decision taken to Reaffirm and Archive |
Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs (Second Revision)
|
June, 2025
|
-
|
Identical under dual numbering
|
|
|
IS 10533:1983 Decision taken to Reaffirm and Archive |
Specification for valve guides for internal combustion engines
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 10651:2019 Decision taken to Reaffirm and Archive |
Hub axle, front for moped - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 10652:2019 Decision taken to Reaffirm and Archive |
Pedal assembly for moped - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 10653:2019 Decision taken to Reaffirm and Archive |
Hub axle, rear, for moped - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 11139:2019 Decision taken to Reaffirm and Archive |
Adjusters for control cables for moped - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 11170:1985 ISO 3046 |
Specification for 1 performance requirements for constant speed compression ignition (Diesel) engines for agricultural purposes (Up To 20 KW)
|
July, 2021
|
4
|
Modified/Technically Equivalent
|
|
|
IS 11509 (Part 1):2012 ISO 4548-1 : 1997 Decision taken to Reaffirm and Archive |
Methods of test for full - Flow lubricating oil filters for internal combustion engines: Part 1 differential pressure/flow characteristics (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 11509 (Part 2):2012 ISO 4548-2 : 1997 Decision taken to Reaffirm and Archive |
Methods of test for full - Flow lubricating oil filters for internal combustion engines: Part 2 element by - Pass valve characteristics (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 11509 (Part 3):2012 ISO 4548-3 : 1997 Decision taken to Reaffirm and Archive |
Methods of test for full - Flow lubricating oil filters for internal combustion engines: Part 3 resistance to high differential pressure and to elevated temperature (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 11509 (Part 5):2023 ISO 4548-5:2020 |
Method of test for full-flow lubricating oil filters for internal combustion engines - Part 5: Test for hydraulic pulse durability
|
-
|
Identical under dual numbering
|
||
|
IS 11838:1986 |
Recommendations for measurement of quality characteristics of gudgeon pins
|
July, 2021
|
1
|
Indigenous
|
|
|
IS 12025:1987 |
Recommendations for measurement of quality characteristics for pistons
|
January, 2024
|
1
|
Indigenous
|
|
|
IS 12352:1988 |
Specification for fuel injection pump mounting bolts
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 12404:1988 |
Specification for couplings for driving fuel injection pumps
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 12455:1988 |
Performance requirements of aircooled spark ignition automotive engines
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 12460:1988 Decision taken to Reaffirm and Archive |
Automotive vehicles - Transmission systems - Manual control sequence in automatic transmissions - Recommendations
|
January, 2024
|
1
|
Indigenous
|
|
|
IS 12499:1988 Decision taken to Reaffirm and Archive |
Specification for two stage, 0.5 litre diesel fuel filters
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 12500:1988 Decision taken to Reaffirm and Archive |
Specification for 0.2 litre diesel fuel filters
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 12535 (Part 1):1988 |
Automotive vehicles - Transmission systems - Glossary: Part 1 general definitions
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 12535 (Part 2):1991 |
Automotive vehicles - Transmission systems - Glonssary: Part 2 universal joints and driveshafts
|
July, 2021
|
-
|
Indigenous
|
|
|
IS 12535 (Part 3):1991 |
Automotive vehicles - Transmission systems - Glossary: Part 3 drive axles definitions
|
July, 2021
|
-
|
Indigenous
|
|
|
IS 12587:1989 |
Automotive vehicles - Transmission system - Gear arrangement - Recommendations
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 12902:1990 ISO 7646 Decision taken to Reaffirm and Archive |
Commercial vehicles and buses - Gearbox flanges - Type A
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12903:1990 ISO 7647 Decision taken to Reaffirm and Archive |
Commercial vehicles and buses - Gearbox flanges - Type S
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12904:1990 ISO 7648 Decision taken to Reaffirm and Archive |
Flywheel housings for reciprocating internal combustion engines - Nominal dimensions and tolerances
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12905:1990 ISO 7653 Decision taken to Reaffirm and Archive |
Commercial Vehicles-couplings Between Power Take-offs (PTO's) and Ancillary Driven Units
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12972:1990 ISO 7707 Decision taken to Reaffirm and Archive |
Commercial road vehicles - Connections for rear - Mounted power take - Offs (PTO)
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12973:1990 ISO 7804 Decision taken to Reaffirm and Archive |
Commercial road vehicles - Side openings for truck power take - Offs (PTO)
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 12978:2006 ISO 8667 |
Commercial vehicles and buses - Cross - Tooth gearbox flanges, type T (First Revision)
|
November, 2020
|
-
|
Identical under dual numbering
|
|
|
IS 12996:1990 Decision taken to Reaffirm and Archive |
Internal combustion engines radiator pressure caps - Specification
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 13016:1991 |
Internal combustion engines - Radiator drain cocks - Specification
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 13018:1990 Decision taken to Reaffirm and Archive |
Internal combustion of test for pressure engines - Method charged engines
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 13029:1991 |
Internal combustionengines - setting ignition timing in spark ignition engines - Code of practice
|
May, 2025
|
-
|
Indigenous
|
|
|
IS 13050:1991 |
Internal combustion engines - Valve seat inserts - Specification
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 13051:1991 |
Internal combustion engines radiator fans - Specification
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 13052:1991 |
Internal combustion engines - Cylinder liners - Quality characteristics
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 13090:2018 ISO 7649 Decision taken to Reaffirm and Archive |
Automotive vehicles - Commercial vehicles - Clutch housings - Dimensions (First Revision)
|
June, 2025
|
-
|
Modified/Technically Equivalent
|
|
|
IS 13686:1993 |
Internal combustion engines radiators - Methods of test
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 13687:1993 |
Internal combustion engines - Radiators - Heat dissipation performance - Method of test
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 13824:1993 |
Internal combustion engines - Method of verification of emission of crankcase gases for vehicles powered with four stroke spark ignition engines
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 14273:1999 |
Automotive vehicles - Exhaust emissions - Gaseous pollutants from vehicles fitted with compression ignition engines - Method of measurement
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 14511 (Part 1):2007 ISO 8984-1 |
Diesel engines - Testing of fuel injectors: Part 1 hand - Lever - Operated testing and setting apparatus (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 14511 (Part 2):2007 ISO 8984-2 |
Diesel engines - Testing of fuel injectors: Part 2 test methods (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 14553:2008 |
Automotive vehicles - Apparatus for the measurement of opacity (Smoke) of exhaust gas from vehicles equipped with compression ignition engines - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 14599:1999 |
Automotive vehicles - Performance requirements (Measurement Of Power, SFC, Opacity) of positive and compression ignition engines - Method of test
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 14600:1999 Decision taken to Reaffirm and Archive |
Automotive vehicles - Exhaust emissions - Gaseous pollutants from vehicles equipped with internal combustion engines - Method of measurement
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 1543:1964 |
Specification for single cylinder fuel injection pumps (Revised)
|
March, 2023
|
1
|
Indigenous
|
|
|
IS 15653:2021 ISO 2710-2:2019 |
Reciprocating internal combustion engine - Vocabulary - Terms for engine maintenance
|
-
|
Identical under dual numbering
|
||
|
IS 16057:2013 |
Lpg operated internal combustion engines - Safety and performance requirements - Specification
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 17019:2018 |
Gear / gerotor oil pump for motorcycle / scooter / moped - Specification
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 17042 (Part 4):2018 ISO 22241-4 : 2009 |
Diesel Engines — NOX Reduction Agent AUS 32 Part 4 Refilling Interface
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 17042 (Part 5):2018 ISO 22241-5 : 2012 |
Diesel engines - Nox reduction agent aus 32: Part 5 refilling interface for passenger cars
|
June, 2025
|
-
|
Identical under dual numbering
|
|
|
IS 19520 (Part 3):2026 |
INTERNAL COMBUSTION ENGINES - PISTON RINGS - PART 3: COIL-SPRING-LOADED OIL CONTROL RINGS MADE OF STEEL
|
-
|
|||
|
IS 19521:2026 |
INTERNAL COMBUSTION ENGINES — PISTON RINGS — EXPANDER RAIL OIL-CONTROL RINGS
|
-
|
|||
|
IS 19538:2026 |
Internal Combustion Engines - Piston Rings - Oil Control Rings
|
-
|
|||
|
IS 2765:1982 |
Specification for radiator hose (First Revision)
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 3169:1991 |
Internal combustion engines - Two stage, one litre, diesel fuel filters (First Revision)
|
November, 2020
|
1
|
Indigenous
|
|
|
IS 3170 (Part 1):2006 ISO 2697 |
Internal Combustion Engines - Fuel Injection Nozzles Part 1 Injection Nozzles - Size `S'
|
November, 2020
|
-
|
Identical under dual numbering
|
|
|
IS 3170 (Part 2):2006 ISO 4010 |
Internal combustion engines - Fuel injection nozzles: Part 2 calibrating nozzle, delay pintle type (First Revision)
|
November, 2020
|
-
|
Identical under dual numbering
|
|
|
IS 3171 (Part 1):1997 ISO 2699 Decision taken to Reaffirm and Archive |
Internal Combustion Engines - Fuel Injection Nozzle Holders - Part 1 : Flange Mounted Fuel Injectors Size `S' Types 2, 3, 4, 5 and 6
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 3171 (Part 2):2006 ISO 7026 Decision taken to Reaffirm and Archive |
Internal Combustion Engines - Fuel Injection Nozzle Holders - Part 2 : Screw-in Injection Nozzle Holders, Types 20, 21, 21.1 and 27 for Pintle Nozzle Size `S', Type B
|
May, 2025
|
-
|
Identical under dual numbering
|
|
|
IS 3171 (Part 3):1997 ISO 7030 Decision taken to Reaffirm and Archive |
Internal combustion engines - Fuel injection nozzle holders: Part 3 screw mounted injection nozzle holders, types 12,13,14,15,16,17,18 and 19
|
November, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 3172:1997 |
Internal combustion engines - Fuel injection equipment - Single and double ended pipe unions (Single And Double Ended Banjo) - Specification (Second Revision)
|
July, 2021
|
1
|
Indigenous
|
|
|
IS 3173:1965 |
Specification for high pressure connections for fuel injection equipment for diesel engines
|
March, 2022
|
-
|
Indigenous
|
|
|
IS 3174:1974 |
Specification for pipe union bolt (First Revision)
|
March, 2023
|
-
|
Indigenous
|
|
|
IS 3175:2013 Decision taken to Reaffirm and Archive |
Internal combustion engine - Sealing washers for pipe unions - Specification (Second Revision)
|
January, 2024
|
-
|
Indigenous
|
|
|
IS 3351:2006 4020 |
Road vehicles - Fuel filters for diesel . engines - Test methods (Second Revision)
|
November, 2020
|
-
|
Identical under dual numbering
|
|
|
IS 3649:2018 |
Automotive vehicles - Clutch facing for automotive transmission - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 4530:2006 |
GeneraL requirements for positioning and routing of engine exhaust pipes in motor vehicles (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 5791:2006 ISO 6621-3 |
Internal combustion engines - Piston rings - Material specifications (Third Revision)
|
November, 2020
|
-
|
Identical under dual numbering
|
|
|
IS/ISO 6621-1:2018 ISO 6621 : Part 1 |
Internal Combustion Engines — Piston Rings Part 1 Vocabulary ( First Revision )
|
June, 2025
|
-
|
Identical under single numbering
|
|
|
IS/ISO 6621-5:2020 |
INTERNAL COMBUSTION ENGINES PISTON RINGS PART 5: QUALITY REQUIREMENTS
|
-
|
|||
|
IS/ISO 6621-2:2020 ISO 6621-2:2020 |
Internal combustion engines - Piston rings - Part 2: Inspection measuring principles
|
-
|
Identical under single numbering
|
||
|
IS 6740:1985 |
Specification for gudgeon pins for internal combustion engines (First Revision)
|
May, 2025
|
1
|
Indigenous
|
|
|
IS 6750:1985 |
Specification for cylinder liners for internal combustion engines (First Revision)
|
May, 2025
|
-
|
Indigenous
|
|
|
IS 7347:1974 |
SPECIFICATION FOR PERFORMANCE OF SMALL SIZE SPARK IGNITION ENGINES FOR AGRICULTURAL WATER PUMPS, SPRAYERS, TILLERS, REAPERS AND OTHER SIMILAR APPLICATIONS
|
August, 2021
|
4
|
Indigenous
|
|
|
IS 7449 (Part 1):1974 Decision taken to Reaffirm and Archive |
Glossary of terms for IC engines: Part 1 fuel injection equipment
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 7451 (Part 6):2007 ISO 2261 |
Reciprocating internal combustion engines: Part 6 hand - Operated control devices - Standard direction of motion (First Revision)
|
January, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 7451 (Part 1):2020 ISO 2710-1 : 2017 |
Reciprocating Internal Combustion Engines — Vocabulary Part 1 Terms for Engine Design and Operation ( Second Revision )
|
June, 2025
|
-
|
Identical under dual numbering
|
|
|
IS 7451 (Part 2):2006 ISO 1204 |
Reciprocating internal combustion engines: Part 2 designation of the direction of rotation and of cylinders and valves in cylinder heads, and definition of right - Hand and left - Hand in - Line engines and locations on an engine (First Revision)
|
July, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7611:1993 |
Internal combustion engines radiators - Specification (First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 7657 (Part 1):1975 |
Specification for starter ring gears for internal combustion engines: Part 1 gears for inertia and solenoid pre - Engaged starters
|
March, 2023
|
1
|
Indigenous
|
|
|
IS 7657 (Part 2):2025 |
STARTER RING GEARS FOR INTERNAL COMBUSTION ENGINES � PART 2: GEARS FOR AXIAL AND COAXIAL STARTERS � SPECIFICATION (First Revision)
|
-
|
Indigenous
|
||
|
IS 810:1991 |
Internal combustion engines - Engine valves - Specification (Second Revision)
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 8118:2008 |
Automotive vehicles - Opacity (Smoke) of exhuast gas from vehicles equipped with compression ignition engines operating under free acceleration - Method of measurement (Third Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS/ISO 8178-7:2015 ISO 8178 : Part 7 : 2015 |
Reciprocating internal combustion engine - Exhaust emission measurement: Part 7 engine family determination (First Revision)
|
November, 2020
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8178-1:2023 ISO 8178-1:2020 |
Reciprocating internal combustion engines Exhaust emission measurement Part 1: Test bed measurement systems of gaseous and particulate emissions
|
-
|
Identical under single numbering
|
||
|
IS/ISO 8178-4:2020 ISO 8178-4:2020 |
Reciprocating internal combustion engines Exhaust emission measurement Part 4: Steady-state and transient test cycles for different engine applications
|
-
|
Identical under single numbering
|
||
|
IS/ISO 8178-3:2019 ISO 8178-3:2019 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 3: Test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using a filter type smoke meter
|
June, 2025
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8178-9:2019 ISO 8178-9:2019 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 9: Test cycles and test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using an opacimeter
|
June, 2025
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8178-8:2015 ISO 8178-8 : 2015 |
Reciprocating internal combustion engines - Exhaust emission measurement: Part 8 engine group determination
|
November, 2020
|
-
|
Identical under single numbering
|
|
|
IS 8422 (Part 1):1977 |
Specification for piston rings for IC engines: Part 1 plain compression rings from 30 up to 200 mm nominal diameter R - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 2):1977 |
Specification for piston rings for IC engines: Part 2 taper faced compression rings from 30 up to 200 mm nominal diameter M - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 3):1977 |
Specification for piston rings for IC engines: Part 3 keystone rings from 82 up to 200 mm nominal diameter T - Rings 15
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 4):1977 |
Specification for piston rings for IC engines: Part 4 napier oil scraper rings from 30 up to 200 mm nominal diameter N - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 5):1977 |
Specification for piston rings for IC engines: Part 5 stepped oil scraper rings from 30 up to 200 mm nominal diameter Z - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 6):1977 |
Specification for piston rings for IC engines: Part 6 slotted oil control rings from 50 up to 200 mm nominal diameter S - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 7):1977 |
Specification for piston rings for IC engines: Part 7 double bevelled slotted oil control rings from 50 up to 200 mm nominal diameter G - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8422 (Part 8):1977 |
Specification for piston rings for IC engines: Part 8 narrow land slotted oil control rings from 50 up to 200 mm nominal diameter D - Rings
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 8503:1986 |
Technical supply conditions for aluminium alloy pistons for internal combustion engines (First Revision)
|
November, 2020
|
-
|
Indigenous
|
|
|
IS/ISO 8528-5:2024 ISO 8528-5:2022 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 5 Generating Sets (Second Revision)
|
-
|
Identical under single numbering
|
||
|
IS/ISO 8528-12:2022 ISO 8528-12:2022 |
RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS PART 12: EMERGENCY POWER SUPPLY TO SAFETY SERVICES (First Revision)
|
-
|
Identical under single numbering
|
||
|
IS/ISO 8528-1:2018 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 1 Application, Ratings and Performance ( First Revision )
|
August, 2024
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-4:2005 |
Reciprocating internal combustion engine driven alternating current generating sets: Part 4 controlgear and switchgear
|
January, 2024
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-6:2005 Decision taken to Reaffirm and Archive |
Reciprocating internal combustion engine driven alternating current generating sets: Part 6 test methods
|
June, 2025
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-7:2017 ISO 8528-7 : 2017 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 7 Technical Declarations for Specification and Design ( First Revision )
|
January, 2024
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-8:2016 ISO 8528-8 : 2016 |
Reciprocating internal combustion engine driven alternating current generating sets: Part 8 requirements and tests for low - Power generating sets (First Revision)
|
January, 2024
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-9:2017 ISO 8528-9 : 2017 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 9 Measurement and Evaluation of Mechanical Vibrations ( First Revision )
|
January, 2024
|
-
|
Identical under single numbering
|
|
|
IS/ISO 8528-2:2018 ISO 8528-2:2018 |
Reciprocating internal combustion engine driven alternating current generating sets - Part 2: Engines
|
-
|
Identical under single numbering
|
||
|
IS/ISO 8528-3:2020 ISO 8528-3:2020 |
Reciprocating internal combustion engine driven alternating current generating sets Part 3: Alternating current generators for generating sets
|
-
|
Identical under single numbering
|
||
|
IS 9262:1979 |
Recommendations for gear positions for road vehicles
|
May, 2025
|
-
|
Indigenous
|
|
|
IS 9418:1980 |
Dimensions for mounting flanges for in - Line fuel injection pumps for multi - Cylinder compressiom ignition engines
|
November, 2020
|
-
|
Indigenous
|
|
|
IS 9420 (Part 1):1988 Decision taken to Reaffirm and Archive |
Specification for feed pumps for diesel fuel injection equipment: Part 1 external dimensions(First Revision)
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 9420 (Part 2):1988 Decision taken to Reaffirm and Archive |
Specification for feed pumps for diesel fuel injection equipment: Part 2 types of drives
|
June, 2025
|
-
|
Indigenous
|
|
|
IS 9465:1980 |
Mounting dimensions for in - Line injection pump assemblies for fuel injection equipment for multi - Cylinder compression ignition engines
|
November, 2020
|
1
|
Indigenous
|
|
|
IS H10001:1981 ISO 3046 |
Specification for performance requirements for constant speed compression ignition (Diesel) engines for general purposes (Up To 20 Kw)
|
July, 2021
|
5
|
Modified/Technically Equivalent
|
| No Records Found |
| No Records Found |
| No Records Found |
| No Records Found | ||
TED 2 (16879)
Revision of: IS 14599:1999 |
AUTOMOTIVE VEHICLES PERFORMANCE REQUIREMENTS MEASUREMENT OF POWER SFC OPACITY OF POSITIVE AND COMPRESSION IGNITION ENGINES METHOD OF TEST First Revision |
|
TED 2 (24507)
|
INTERNAL COMBUSTION ENGINES PISTON RINGS PART 4 GENERAL SPECIFICATIONS |
|
TED 2 (24509)
|
INTERNAL COMBUSTION ENGINES - PISTON RINGS PART 2 COIL-SPRING-LOADED OIL CONTROL RINGS OF NARROW WIDTH MADE OF CAST IRON |
|
TED 2 (00956)
|
Reciprocating internal combustion engines Exhaust emission measurement Part 9 Test cycles and procedures for test-bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions | |
|
TED 2 (00951)
|
Reciprocating internal combustion engines - Fire protection | |
|
TED 2 (00952)
|
Reciprocating Internal Combustion Engine - Exhaust Emission Measurement - Part 3 Definitions and Methods of Measurement of Exhaust Gas Smoke Under Steady - State Conditions | |
|
TED 2 (00929)
Revision of: IS 3649:2018 |
Automotive Vehicles - Clutch Facing for Automotive Transmission - Specification First Revision | |
|
TED 2 (00930)
Revision of: IS 13090:2018 |
Automotive Vehicles - Commercial Vehicles - Clutch Housings - Dimensions First Revision | |
|
TED 2 (11965)
Revision of: IS 10478:2018 |
Diesel Engines - Fuel Injection Pumps - Tapers for Shaft Ends and Hubs Second Revision | |
|
TED 2 (12054)
Revision of: IS 10651:2019 |
Specification for hub axle front for mopeds | |
|
TED 2 (12056)
Revision of: IS 10653:2019 |
Specification for hub axle rear for mopeds | |
|
TED 2 (12058)
Revision of: IS 10653:2019 |
Specification for Pedal Assembly for Mopeds | |
|
TED 2 (12060)
Revision of: IS 11139:2019 |
Specification for Adjusters for Control Cables for Mopeds | |
|
TED 2 (12062)
Revision of: IS 10323:2019 |
Specification for Crank and Chain Wheel for Mopeds | |
|
TED 2 (12066)
Revision of: IS 11509:2006 |
Methods of test for full-flow lubricating oil filters for internal combustion engines- Part 6 Test for cold start simulation and hydraulic pulse durability second revision | |
|
TED 2 (12069)
|
Reciprocating internal combustion engines-Exhaust emission measurement-Part 1 Test-bed measurement systems of gaseous and particulate emission | |
|
TED 2 (12070)
|
Reciprocating internal combustion engines - Exhaust emission measurement - Part 8 Engine group determination | |
|
TED 2 (12071)
Revision of: IS/ISO 8178:2015 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 7 Engine family determination | |
|
TED 2 (12073)
Revision of: IS/ISO 8528:2016 |
Reciprocating internal combustion engines driven alternating current generating sets - Part 8 Requirements and tests for low-power generating sets | |
|
TED 2 (12459)
|
Gear oil pump for motorcycle - Specification | |
|
TED 2 (13687)
Revision of: IS 7451:2020 |
Reciprocating internal combustion engines - Vocabulary - Part 1 Terms for engine design and operation | |
|
TED 2 (13692)
Revision of: IS/ISO 6621:2018 |
Internal combustion engines - Piston rings - Part 1 Vocabulary | |
|
TED 2 (13716)
Revision of: IS/ISO 8528:2017 |
Reciprocating internal combustion engines driven alternating current generating sets - Part 9 Measurement and evaluation of mechanical vibration | |
|
TED 2 (13717)
Revision of: IS/ISO 8528:2018 |
Reciprocating internal combustion engines driven alternating current generating sets - Part 5 Generating sets | |
|
TED 2 (13718)
Revision of: IS/ISO 8528:2018 |
Reciprocating internal combustion engines driven alternating current generating sets - Part 1 Application ratings and performance | |
|
TED 2 (13720)
Revision of: IS/ISO 8528:2017 |
Reciprocating internal combustion engines driven alternating current generating sets - Part 7 Technical declarations for specification and design | |
|
TED 2 (13721)
Revision of: IS/ISO 8178:2017 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 4 Steady-state test cycles for different engine applications | |
|
TED 2 (16117)
Revision of: IS 15653:2006 |
Reciprocating internal combustion engine - Vocabulary - Terms for engine maintenance | |
|
TED 2 (16120)
Revision of: IS/ISO 8528:2005 |
Reciprocating internal combustion engine driven alternating current generating sets - Part 2 Engines | |
|
TED 2 (16121)
Revision of: IS/ISO 8178:1994 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 3 Test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using a filter type smoke meter | |
|
TED 2 (16129)
Revision of: IS/ISO 8178:2018 |
Reciprocating internal combustion engines - Exhaust emission measurement - Part 9 Test cycles and test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using an opacimeter | |
|
TED 2 (16665)
|
Specification for performance of small size spark ignition engines for agricultural pumps sprayers tillers reapers and other similar applications Amendment - 4 | |
|
TED 2 (17750)
Revision of: IS 11509:2018 |
Method of test for full-flow lubricating oil filters for internal combustion engines - Part 5 Test for hydraulic pulse durability | |
|
TED 2 (17755)
Revision of: IS/ISO 6621:2003 |
Internal combustion engines - Piston rings - Part 2 Inspection measuring principles | |
|
TED 2 (17757)
Revision of: IS/ISO 8178:2017 |
Reciprocating internal combustion engines Exhaust emission measurement Part 1 Test bed measurement systems of gaseous and particulate emissions | |
|
TED 2 (17758)
Revision of: IS/ISO 8178:2017 |
Reciprocating internal combustion engines Exhaust emission measurement Part 4 Steady-state and transient test cycles for different engine applications | |
|
TED 2 (17759)
Revision of: IS/ISO 8528:2005 |
Reciprocating internal combustion engine driven alternating current generating sets Part 3 Alternating current generators for generating sets | |
|
TED 2 (17821)
|
Specification for performance requirements for constant speed compression ignition Diesel engines for general purposes Above 20 KW Amendment - 1 | |
|
TED 2 (20895)
Revision of: IS 3174:1974 |
PIPE UNION BOLT SPECIFICATION Second Revision | |
|
TED 2 (20898)
Revision of: IS 7657:1975 |
STARTER RING GEARS FOR INTERNAL COMBUSTION ENGINES PART 2 GEARS FOR AXIAL AND COAXIAL STARTERS SPECIFICATION First Revision | |
|
TED 2 (20900)
Revision of: IS 7657:1975 |
Starter Ring Gears for Internal Combustion Engines Specification Part 1 Gears for Inertia and Solenoid Pre-Engaged Starters First Revision | |
|
TED 2 (20906)
Revision of: IS 8422:1977 |
SPECIFICATION FOR PISTON RINGS FOR IC ENGINES PART 5 STEPPED OIL SCRAPER RINGS FROM 30 UP TO 200 mm NOMINAL DIAMETER Z-RINGS | |
|
TED 2 (22709)
Revision of: IS 17458:2018 |
Reciprocating Internal Combustion Engines Fire Protection First Revision | |
|
TED 2 (23099)
Revision of: IS 7611:1993 |
INTERNAL COMBUSTION ENGINES RADIATORS SPECIFICATION | |
|
TED 2 (23100)
Revision of: IS 13686:1993 |
Internal Combustion Engines Radiators Methods of Test | |
|
TED 2 (23120)
Revision of: IS 13687:1993 |
Internal Combustion Engines Radiators Heat Dissipation Performance Method Of Test | |
|
TED 2 (23237)
Revision of: IS 14273:1999 |
AUTOMOTIVE VEHICLES - EXHAUST EMISSIONS - GASEOUS POLLUTANTS FROM VEHICLES FITTED WITH COMPRESSION IGNITION ENGINES - METHOD OF MEASUREMENT First Revision | |
|
TED 2 (23613)
Revision of: IS/ISO 8528:2018 |
RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS PART 5 GENERATING SETS Second Revision | |
|
TED 2 (23614)
Revision of: IS/ISO :1998 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 10 Measurement of Airborne Noise First Revision | |
|
TED 2 (23615)
Revision of: IS/ISO 8528:1997 |
RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS PART 12 EMERGENCY POWER SUPPLY TO SAFETY SERVICES First Revision | |
|
TED 2 (24458)
Revision of: IS 7347:1974 |
SMALL SIZE SPARK IGNITION ENGINES FOR AGRICULTURAL WATER PUMPS SPRAYERS TILLERS REAPERS AND OTHER SIMILAR APPLICATIONS PERFORMANCE SPECIFICATION First Revision | |
|
TED 2 (24508)
|
INTERNAL COMBUSTION ENGINES PISTON RINGS PART 5 QUALITY REQUIREMENTS | |
|
TED 2 (24510)
|
INTERNAL COMBUSTION ENGINES - PISTON RINGS - PART 3 COIL-SPRING-LOADED OIL CONTROL RINGS MADE OF STEEL | |
|
TED 2 (24511)
|
INTERNAL COMBUSTION ENGINES PISTON RINGS EXPANDER RAIL OIL-CONTROL RINGS | |
|
TED 2 (24621)
IS 8422:1977 |
Internal Combustion Engines - Piston Rings - Oil Control Rings | |
|
TED 2 (33782)
|
Internal combustion engines - Piston rings - Material specifications |
|
|
IS 10003:1988 |
Compression Ignition Diesel Engines For Automotive Application |
|
|
IS 10004:1981 |
Performance Requirements for Spark Ignition Engines for Automotive Purposes |
|
|
IS 11509 (Part 6):2006 ISO 4548-5 |
Methods of test for full - Flow lubricating oil filters for internal combustion engines Part 6 cold start simulation and hydraulic pulse durability test First Revision |
|
|
IS 12022:1987 |
Methods of Testing of Quality Characteristics for Piston Rings |
|
|
IS 12969:1990 |
Internal Combustion Engines - Methods of Test for Quality Characteristics of Valves |
|
|
IS 12971:1990 ISO 7706 |
Road vehicles - Commercial vehicles clearance envelope for power take - Offs PTO |
|
|
IS 14511:1998 |
Automotive Vehicles - Testing of fuel Injectors - Hand Lever Testing Apparatus |
|
|
IS 14555:1998 |
Automotive Vehicles - Evaporative Emissions from Vehicles Equipped with Spark Ignition Engines - Method of Measurement |
|
|
IS 14556:1998 |
Automotive Vehicles - Catalytic Converters for Spark Ignition Engines - Installed Requirements |
|
|
IS 1600:1960 |
Code For Type Testing Of Constant Speed Internal Combustion Engines For General Purpose |
|
|
IS 1601:1960 |
Performance of constant speed internal combustion engines for general purposes |
|
|
IS 1602:1960 |
Code for type testing of variable speed internal combustion engines for automotive purposes |
|
|
IS 1603:1960 |
Performance of variable-speed internal combustion engines for automotive purpose |
|
|
IS 17458:2018 ISO 6826 : 1997 |
Reciprocating internal combustion engine - Fire protection |
|
|
IS 3511:1966 |
Cylinder bore diameters for internal combustion engines |
|
|
IS 7451 (Part 3):1974 |
Reciprocating Internal Combustion Engines - Part III Definition of Right-Hand and Left-Hand Single Bank Engines |
|
|
IS 7451 (Part 4):1974 |
Reciprocating Internal Combustion Engines - Part IV Designation of Direction of Rotation |
|
|
IS 7451 (Part 5):1974 |
Reciprocating Internal Combustion Engines - Part V Designation of the Cylinders |
|
|
IS 8422 (Part 9):1986 |
Piston rings for lC engines Part 9 Terms and Definitions |
|
IS 10001:1981 ISO 3046 |
Performance Requirements for Constant Speed Compression ignition diesel engines for general purposes up to 20 kW |
|
|
IS 10002:1981 ISO 3046 |
Specification for performance requirements for constant speed compression ignition Diesel engines for general purposes Above 20 KW |
|
|
IS 10105:1982 Decision taken to Reaffirm and Archive |
Specification for fittings for cylinder pressure indicators for internal combustion engines |
|
|
IS 10323:2019 Decision taken to Reaffirm and Archive |
Crank and chain wheel for moped - Specification First Revision |
|
|
IS 10533:1983 Decision taken to Reaffirm and Archive |
Specification for valve guides for internal combustion engines |
|
|
IS 10651:2019 Decision taken to Reaffirm and Archive |
Hub axle front for moped - Specification First Revision |
|
|
IS 10652:2019 Decision taken to Reaffirm and Archive |
Pedal assembly for moped - Specification First Revision |
|
|
IS 10653:2019 Decision taken to Reaffirm and Archive |
Hub axle rear for moped - Specification First Revision |
|
|
IS 11139:2019 Decision taken to Reaffirm and Archive |
Adjusters for control cables for moped - Specification First Revision |
|
|
IS 11170:1985 ISO 3046 |
Specification for 1 performance requirements for constant speed compression ignition Diesel engines for agricultural purposes Up To 20 KW |
|
|
IS 12352:1988 |
Specification for fuel injection pump mounting bolts |
|
|
IS 12404:1988 |
Specification for couplings for driving fuel injection pumps |
|
|
IS 12455:1988 |
Performance requirements of aircooled spark ignition automotive engines |
|
|
IS 12460:1988 Decision taken to Reaffirm and Archive |
Automotive vehicles - Transmission systems - Manual control sequence in automatic transmissions - Recommendations |
|
|
IS 12499:1988 Decision taken to Reaffirm and Archive |
Specification for two stage 0 5 litre diesel fuel filters |
|
|
IS 12500:1988 Decision taken to Reaffirm and Archive |
Specification for 0 2 litre diesel fuel filters |
|
|
IS 12535 (Part 2):1991 |
Automotive vehicles - Transmission systems - Glonssary Part 2 universal joints and driveshafts |
|
|
IS 12902:1990 ISO 7646 Decision taken to Reaffirm and Archive |
Commercial vehicles and buses - Gearbox flanges - Type A |
|
|
IS 12903:1990 ISO 7647 Decision taken to Reaffirm and Archive |
Commercial vehicles and buses - Gearbox flanges - Type S |
|
|
IS 12905:1990 ISO 7653 Decision taken to Reaffirm and Archive |
Commercial Vehicles-couplings Between Power Take-offs PTO s and Ancillary Driven Units |
|
|
IS 12972:1990 ISO 7707 Decision taken to Reaffirm and Archive |
Commercial road vehicles - Connections for rear - Mounted power take - Offs PTO |
|
|
IS 12973:1990 ISO 7804 Decision taken to Reaffirm and Archive |
Commercial road vehicles - Side openings for truck power take - Offs PTO |
|
|
IS 12978:2006 ISO 8667 |
Commercial vehicles and buses - Cross - Tooth gearbox flanges type T First Revision |
|
|
IS 12996:1990 Decision taken to Reaffirm and Archive |
Internal combustion engines radiator pressure caps - Specification |
|
|
IS 13016:1991 |
Internal combustion engines - Radiator drain cocks - Specification |
|
|
IS 13050:1991 |
Internal combustion engines - Valve seat inserts - Specification |
|
|
IS 13051:1991 |
Internal combustion engines radiator fans - Specification |
|
|
IS 13052:1991 |
Internal combustion engines - Cylinder liners - Quality characteristics |
|
|
IS 1543:1964 |
Specification for single cylinder fuel injection pumps Revised |
|
|
IS 16057:2013 |
Lpg operated internal combustion engines - Safety and performance requirements - Specification |
|
|
IS 17019:2018 |
Gear gerotor oil pump for motorcycle scooter moped - Specification |
|
|
IS 2765:1982 |
Specification for radiator hose First Revision |
|
|
IS 3169:1991 |
Internal combustion engines - Two stage one litre diesel fuel filters First Revision |
|
|
IS 3170 (Part 1):2006 ISO 2697 |
Internal Combustion Engines - Fuel Injection Nozzles Part 1 Injection Nozzles - Size S |
|
|
IS 3170 (Part 2):2006 ISO 4010 |
Internal combustion engines - Fuel injection nozzles Part 2 calibrating nozzle delay pintle type First Revision |
|
|
IS 3171 (Part 2):2006 ISO 7026 Decision taken to Reaffirm and Archive |
Internal Combustion Engines - Fuel Injection Nozzle Holders - Part 2 Screw-in Injection Nozzle Holders Types 20 21 21 1 and 27 for Pintle Nozzle Size S Type B |
|
|
IS 3171 (Part 3):1997 ISO 7030 Decision taken to Reaffirm and Archive |
Internal combustion engines - Fuel injection nozzle holders Part 3 screw mounted injection nozzle holders types 12 13 14 15 16 17 18 and 19 |
|
|
IS 3171 (Part 1):1997 ISO 2699 Decision taken to Reaffirm and Archive |
Internal Combustion Engines - Fuel Injection Nozzle Holders - Part 1 Flange Mounted Fuel Injectors Size S Types 2 3 4 5 and 6 |
|
|
IS 3172:1997 |
Internal combustion engines - Fuel injection equipment - Single and double ended pipe unions Single And Double Ended Banjo - Specification Second Revision |
|
|
IS 3173:1965 |
Specification for high pressure connections for fuel injection equipment for diesel engines |
|
|
IS 3174:1974 |
Specification for pipe union bolt First Revision |
|
|
IS 3175:2013 Decision taken to Reaffirm and Archive |
Internal combustion engine - Sealing washers for pipe unions - Specification Second Revision |
|
|
IS 3649:2018 |
Automotive vehicles - Clutch facing for automotive transmission - Specification First Revision |
|
|
IS 4530:2006 |
GeneraL requirements for positioning and routing of engine exhaust pipes in motor vehicles First Revision |
|
|
IS 5791:2006 ISO 6621-3 |
Internal combustion engines - Piston rings - Material specifications Third Revision |
|
|
IS 6740:1985 |
Specification for gudgeon pins for internal combustion engines First Revision |
|
|
IS 6750:1985 |
Specification for cylinder liners for internal combustion engines First Revision |
|
|
IS 7347:1974 |
SPECIFICATION FOR PERFORMANCE OF SMALL SIZE SPARK IGNITION ENGINES FOR AGRICULTURAL WATER PUMPS SPRAYERS TILLERS REAPERS AND OTHER SIMILAR APPLICATIONS |
|
|
IS 7451 (Part 6):2007 ISO 2261 |
Reciprocating internal combustion engines Part 6 hand - Operated control devices - Standard direction of motion First Revision |
|
|
IS 7611:1993 |
Internal combustion engines radiators - Specification First Revision |
|
|
IS 7657 (Part 1):1975 |
Specification for starter ring gears for internal combustion engines Part 1 gears for inertia and solenoid pre - Engaged starters |
|
|
IS 7657 (Part 2):2025 |
STARTER RING GEARS FOR INTERNAL COMBUSTION ENGINES PART 2 GEARS FOR AXIAL AND COAXIAL STARTERS SPECIFICATION First Revision |
|
|
IS 810:1991 |
Internal combustion engines - Engine valves - Specification Second Revision |
|
|
IS 8422 (Part 6):1977 |
Specification for piston rings for IC engines Part 6 slotted oil control rings from 50 up to 200 mm nominal diameter S - Rings |
|
|
IS 8422 (Part 3):1977 |
Specification for piston rings for IC engines Part 3 keystone rings from 82 up to 200 mm nominal diameter T - Rings 15 |
|
|
IS 8422 (Part 7):1977 |
Specification for piston rings for IC engines Part 7 double bevelled slotted oil control rings from 50 up to 200 mm nominal diameter G - Rings |
|
|
IS 8422 (Part 8):1977 |
Specification for piston rings for IC engines Part 8 narrow land slotted oil control rings from 50 up to 200 mm nominal diameter D - Rings |
|
|
IS 8422 (Part 4):1977 |
Specification for piston rings for IC engines Part 4 napier oil scraper rings from 30 up to 200 mm nominal diameter N - Rings |
|
|
IS 8422 (Part 1):1977 |
Specification for piston rings for IC engines Part 1 plain compression rings from 30 up to 200 mm nominal diameter R - Rings |
|
|
IS 8422 (Part 5):1977 |
Specification for piston rings for IC engines Part 5 stepped oil scraper rings from 30 up to 200 mm nominal diameter Z - Rings |
|
|
IS 8422 (Part 2):1977 |
Specification for piston rings for IC engines Part 2 taper faced compression rings from 30 up to 200 mm nominal diameter M - Rings |
|
|
IS/ISO 8528-1:2018 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 1 Application Ratings and Performance First Revision |
|
|
IS/ISO 8528-7:2017 ISO 8528-7 : 2017 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 7 Technical Declarations for Specification and Design First Revision |
|
|
IS/ISO 8528-4:2005 |
Reciprocating internal combustion engine driven alternating current generating sets Part 4 controlgear and switchgear |
|
|
IS/ISO 8528-8:2016 ISO 8528-8 : 2016 |
Reciprocating internal combustion engine driven alternating current generating sets Part 8 requirements and tests for low - Power generating sets First Revision |
|
|
IS/ISO 8528-12:2022 ISO 8528-12:2022 |
RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS PART 12 EMERGENCY POWER SUPPLY TO SAFETY SERVICES First Revision |
|
|
IS/ISO 8528-5:2024 ISO 8528-5:2022 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets Part 5 Generating Sets Second Revision |
|
|
IS/ISO 8528-2:2018 ISO 8528-2:2018 |
Reciprocating internal combustion engine driven alternating current generating sets - Part 2 Engines |
|
|
IS 9420 (Part 2):1988 Decision taken to Reaffirm and Archive |
Specification for feed pumps for diesel fuel injection equipment Part 2 types of drives |
|
|
IS H10001:1981 ISO 3046 |
Specification for performance requirements for constant speed compression ignition Diesel engines for general purposes Up To 20 Kw |